p-port project
#26
Registered shy guy
iTrader: (1)
Join Date: Jul 2007
Location: tewksbury, ma
Posts: 1,436
Likes: 0
Received 0 Likes
on
0 Posts
iam in the same boat as you trying to build your car and save cash where you can, thats why iam buying a sp 12a with low miles from a member instead of buying a fresh rebuilt from some of the bigger names . saving close to 1400$ isnt bad in my book.
#31
13b P-port on a budget
Thread Starter
Join Date: Nov 2004
Location: Louisville KY
Posts: 3,003
Likes: 0
Received 0 Likes
on
0 Posts
#32
Double Ds for me to share
#35
Double Ds for me to share
nick812 I bought the engine from my father inlaw. The housings were made back in the '80s from a '70s 13B, the rotors and eshaft are from a GSL-SE. I didn't have to do anything except buy my seals and assemble her.
Stevan I'm running a dual 2" system with four mufflers.
Stevan I'm running a dual 2" system with four mufflers.
#39
Double Ds for me to share
the weber is not tunned for the PP. It came off my 1/2 bridged 12a and then it wasn't even tunned for that. The weber is jetted for a 12a streetport but still starts and lets the car run and idle. Lean very lean but this will change once the new tranny, flywheel and clutch is in. Cause once that is in then i can stick her back on the dyno and tune the weber as best as i can for this setup till i microtech it and add nos.
#40
Junior Member
Join Date: Feb 2008
Location: reading pa
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
the best carb a p-port engine are webber the bigger the better like 58 and 62 webber like the ones used on vw check out geneberg.com they modified any webber carb from 51 to 58 or u can also get a manifold 2 fit a 4bbl carb or a 4500 dominator the people at newimportspeedshop.comfl do this u can also get webber custom made 4 ur app give them a call 813-936-3222
#42
Junior Member
Join Date: Feb 2008
Location: reading pa
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
check these webbers out http://dragueo.tv/home/reportajes/genesis/images/4.jpg
#45
Rotary Enthusiast
iTrader: (4)
Join Date: Jun 2005
Location: Vancouver WA
Posts: 847
Likes: 0
Received 0 Likes
on
0 Posts
I run Dual 2" all the way through 2 presilencers and 2 walker super turbo mufflers under the car,then the tailpipe over the axle and out the back,never collecting,it sounds so much better than when the mufflers are at the back of the car,oh this system is on my RX-3SP Peripheral Port,as far as power it made 288rwhp and that was with the 51 IDA,i am in the process of putting FI on the engine,and 175 shot of nitrous,i think it will kick some *** when it's done.
#50
Eats, Sleeps, Dreams Rotary
iTrader: (1)
I run Dual 2" all the way through 2 presilencers and 2 walker super turbo mufflers under the car,then the tailpipe over the axle and out the back,never collecting,it sounds so much better than when the mufflers are at the back of the car,oh this system is on my RX-3SP Peripheral Port,as far as power it made 288rwhp and that was with the 51 IDA,i am in the process of putting FI on the engine,and 175 shot of nitrous,i think it will kick some *** when it's done.