My Suspension Buildup Thread
#1
My Suspension Buildup Thread
I thought that I would put together a thread to update the suspension work that I've been doing on my 83 GS. I finally got most of the parts I need and will be doing the following:
-Tokico HPs
-RB Springs
-Full ES Bushing kit
-New drums and rotors
-New Pads & Shoes
-New front calipers
-Repack wheel bearings
-Rubber undercoating the wheel wells
-Hopefully some braided stainless brake lines
Anyway, I've got most of the parts ready to go so I thought that I would go ahead and dive in. The shocks, struts, and front rotors are already apart so I had a pretty good first night. I'm working on those blasted locknuts on the top of the struts. I've got a friend who is going to let me borrow his impact gun, so that will hopefully zip them right off of there....
Here is the majority of the parts, all laid out for a final check. It would appear that everything is ready to go...
Here is Rosie up on jackstands, preparing herself for the long operation that is about to begin.
The racing beat springs are ready to be painted....
Here is the paint that I decided to try. It ended up working out okay. It doesn't cover very well, but dries fast, and is pretty hard...
Struts are off!
Shocks are off!!
-Tokico HPs
-RB Springs
-Full ES Bushing kit
-New drums and rotors
-New Pads & Shoes
-New front calipers
-Repack wheel bearings
-Rubber undercoating the wheel wells
-Hopefully some braided stainless brake lines
Anyway, I've got most of the parts ready to go so I thought that I would go ahead and dive in. The shocks, struts, and front rotors are already apart so I had a pretty good first night. I'm working on those blasted locknuts on the top of the struts. I've got a friend who is going to let me borrow his impact gun, so that will hopefully zip them right off of there....
Here is the majority of the parts, all laid out for a final check. It would appear that everything is ready to go...
Here is Rosie up on jackstands, preparing herself for the long operation that is about to begin.
The racing beat springs are ready to be painted....
Here is the paint that I decided to try. It ended up working out okay. It doesn't cover very well, but dries fast, and is pretty hard...
Struts are off!
Shocks are off!!
#2
The old rotors are off and ready to have the wheel bearings and races removed....
Wheel bearings and all associated parts have been removed from the rotor. They are ready to be cleaned up...
Bearings are all cleaned and ready to go into the new rotor!
A better closeup of the clean parts....
What's left of the front suspension so far....
The rears ready to be taken apart....
That's it for now! Stay tuned for more when I get the impact gun to break those dern nuts off of my struts!
Jamie
Glazedham42
Wheel bearings and all associated parts have been removed from the rotor. They are ready to be cleaned up...
Bearings are all cleaned and ready to go into the new rotor!
A better closeup of the clean parts....
What's left of the front suspension so far....
The rears ready to be taken apart....
That's it for now! Stay tuned for more when I get the impact gun to break those dern nuts off of my struts!
Jamie
Glazedham42
#5
Junior Member
Join Date: Nov 2007
Location: SF Bay Area
Posts: 27
Likes: 0
Received 0 Likes
on
0 Posts
Suspension
Good post. I'm planning on doing pretty much the same to my 85 GSL SE and look forward to watching your progress. With all the new parts, why not install new bearings?
#6
No love for the rear brakes huh Jeff? I heavily contemplated finding a LSD rear end, but they were all about $200. And those were the ones that needed quite a bit of TLC. So I figured to get the LSD rear, with disc brakes, swap everything over, get it cleaned up, and all the parts repaired and replaced I'd be looking at $300-400. I decided just to stick with what I've got for now. It's a good rear end, and gets the job done for now. Maybe someday I'll make the switch...
#8
http://www.epi-eng.com/BAS-BearingLife.htm
#10
I hate this f0rum
iTrader: (2)
I'm doing pretty much the same thing right now. Except instead of new brake rotors and drums, I opted for respeed coilovers and illumina's. I'm also doing tie rod ends and ball joints.
Question for you. Are you going to re-paint your strut housings or leave them all nasty and rusty?
Question for you. Are you going to re-paint your strut housings or leave them all nasty and rusty?
#11
They are just OE replacements that I got from Carquest. I'm not sure if you have Carquest stores over in Ohio, but for some reason they can get rotors and drums for about half the cost of Autozone. I got the front and back together for $120. Pretty good deal if you ask me.
The rear drums actually look functionally nicer than the old ones that are on the car right now. As you mentioned the cooling fins look a little different. I'll let you know what I think of them when I step on the pedal for the first time...
#12
After I get the inserts out of the front struts I'm going to wirebrush and sand them down so they are clean and smooth. Then they will be getting several generous coats of Duplicolor Ford Blue engine paint. Then I might hit them with some wheel clear coat when I'm done, just to keep the paint from chipping off. I'll be sure to post pictures....
#13
Senior Member
The difference between that OEM spring and RB spring is amazing. Looks good, I can't wait to do this to my car. Where did you get all your parts? What other wear items are replacing in regards to the suspension/steering?
#14
I hate this f0rum
iTrader: (2)
After I get the inserts out of the front struts I'm going to wirebrush and sand them down so they are clean and smooth. Then they will be getting several generous coats of Duplicolor Ford Blue engine paint. Then I might hit them with some wheel clear coat when I'm done, just to keep the paint from chipping off. I'll be sure to post pictures....
#15
The Tokico HPs I got on E-bay for $160 shipped. They were listed for $184 but I made an offer and they took it. I got the RB springs from another forum member, and they are gently used. The energy suspension kit I got from EnergySuspensionParts.com. It was the best price I could find, and they threw in the front strut rod bushings at no extra cost. For some reason the other kits I looked at didn't include those bushings.
Jamie
Jamie
#17
Lapping = Fapping
iTrader: (13)
No love for the rear brakes huh Jeff? I heavily contemplated finding a LSD rear end, but they were all about $200. And those were the ones that needed quite a bit of TLC. So I figured to get the LSD rear, with disc brakes, swap everything over, get it cleaned up, and all the parts repaired and replaced I'd be looking at $300-400. I decided just to stick with what I've got for now. It's a good rear end, and gets the job done for now. Maybe someday I'll make the switch...
#18
The car or the rear end? I'll most likely end up doing this swap at some point in the future. Right now money is kinda tight for me to be changing anything that isn't broken or ineffective. All the parts I'm replacing are worn out anyway, so I can justify buying the HPs and the ES kit pretty easily. I'd have a hard time replacing a functioning rear end when I only get $100 a month to play with.
This is my first time ever messing with the suspension on any car, so I think it will do me some good to figure out how everything works before I go changing it around. I'm looking forward to working on something new for a change.
This is my first time ever messing with the suspension on any car, so I think it will do me some good to figure out how everything works before I go changing it around. I'm looking forward to working on something new for a change.
#19
Lapping = Fapping
iTrader: (13)
Did all S models have drums?
I was just going to put a 12A in it and sell it, but the cool LSD rear end and the way it drove convinced me to keep it. Now I'm even contemplating a 20B install. All I've got to do is put another 12A in it, drive it around for a while and compare it to another possible 20B candidate. Then make my final decision.
I was just going to put a 12A in it and sell it, but the cool LSD rear end and the way it drove convinced me to keep it. Now I'm even contemplating a 20B install. All I've got to do is put another 12A in it, drive it around for a while and compare it to another possible 20B candidate. Then make my final decision.
#21
Do you have any advice on burning out the bushings? Do you heat them up and then press them out while they are still hot or just burn them all the way out? I haven't done this before so I'm looking for tips. I do have access to a torch, which will help.
What is the easiest way to get the new bushings in? Billy from Respeed told me that a bench vise will work if used properly. I don't have a bearing press unfortunately...
What is the easiest way to get the new bushings in? Billy from Respeed told me that a bench vise will work if used properly. I don't have a bearing press unfortunately...
#22
Did all S models have drums?
I was just going to put a 12A in it and sell it, but the cool LSD rear end and the way it drove convinced me to keep it. Now I'm even contemplating a 20B install. All I've got to do is put another 12A in it, drive it around for a while and compare it to another possible 20B candidate. Then make my final decision.
I was just going to put a 12A in it and sell it, but the cool LSD rear end and the way it drove convinced me to keep it. Now I'm even contemplating a 20B install. All I've got to do is put another 12A in it, drive it around for a while and compare it to another possible 20B candidate. Then make my final decision.
The other 20B candidate is the GLC right? I'd like to see either of those projects come to fruition. Although I'm a diehard 1st gen guy, I think that I have to root for the GLC to get the 20B. There's just something about it being so wrong that it's right. Good luck getting either of those cars to hook up with a 20B powering the rear wheels. What a great problem to have.....
#24
Do you have any advice on burning out the bushings? Do you heat them up and then press them out while they are still hot or just burn them all the way out? I haven't done this before so I'm looking for tips. I do have access to a torch, which will help.
What is the easiest way to get the new bushings in? Billy from Respeed told me that a bench vise will work if used properly. I don't have a bearing press unfortunately...
What is the easiest way to get the new bushings in? Billy from Respeed told me that a bench vise will work if used properly. I don't have a bearing press unfortunately...
Drill a series of holes around the bushing and then burn them out with a torch. Just let them burn away over a tin can or something
#25
Say What?
Join Date: Jun 2007
Location: Oak Harbor,WA and Santa Maria, CA
Posts: 1,239
Likes: 0
Received 0 Likes
on
0 Posts