my motor
11-27-06, 10:29 AM
#26
Will you just please follow the basic steps 1st then report the results.
Compression test results
Ignition test results
Fuel test results.
Stop making this harder then it has to be, especially on the people that are trying to help.
The procedures are all straight forward and only take a small amount of time to verify.
After we get the test results then we can brainstorm...
Compression test results
Ignition test results
Fuel test results.
Stop making this harder then it has to be, especially on the people that are trying to help.
The procedures are all straight forward and only take a small amount of time to verify.
After we get the test results then we can brainstorm...
11-27-06, 07:09 PM
#27
Wankel Me This!!
Thread Starter
ok I wll do the tests next week end and I need to get my car up on the jack stands because I had to move it so we can put another car inthere so we can work on my aunts car. So when I clean my fuel system do I take it off? And what would i clean it with?
Oh and another thing. Would it be easyer to clean the fuel system with that stuff you need the etest stuff off?
Oh and another thing. Would it be easyer to clean the fuel system with that stuff you need the etest stuff off?
11-27-06, 07:45 PM
#28
voo doo witchdoctor
Join Date: Aug 2005
Location: Texarkana, Arkansas
Posts: 365
Likes: 0
Received 0 Likes
on
0 Posts
im looking at this pic of yours and noticing that your smog pump is missing. wouldnt that cause some kind of a vac. leak if the acv and nest havent been removed and blocked off properly?
12-20-06, 08:22 AM
#31
Wankel Me This!!
Thread Starter
Hi I am puting a post in here because I dont want to start a new thread. Ok last night me and my buddy tryed to start my car. We tryed to jump start it but the motor is not turning over. He was reving his vans motor at redline but it did not work and we are going to try again this thursday. This moning I was talking to my dad after his work. I told him what we tryed. The cluch was pushed in. So my dad was asking is the cluch hydrolic cluch or the other kind. So I look in my rx7 parts book.(i for got the name) And it have a cluch sentser. So my dad said the cluch sentser is shot or not on or not put on right. I am asking could this be the problem or somthing else?
12-20-06, 08:32 AM
#33
Wankel Me This!!
Thread Starter
Originally Posted by Dan_s_young
Huh, a clutch sentser eh?
Lol, we have hydraulic clutches. Try turning the motor over using a ratchet and if it won't go, don't even consider trying with the starter. You will just cause yourself more grief.
Lol, we have hydraulic clutches. Try turning the motor over using a ratchet and if it won't go, don't even consider trying with the starter. You will just cause yourself more grief.
ya because you need the cluch pushed all the way in so it will start. but the sentser but not be broken and maybe that why the motor is not turning over.
12-20-06, 09:42 AM
#34
No. More then likely your battery is discharged. Take the battery out and have it charged and tested. You cannot jump start thru a battery that is either "Completley discharged", Or a battery that has a dead cell. any battery that will fit and has the connections on the correct side will do. Also clean the battery cables.
83's did not have a clutch inhibitor switch on them.
83's did not have a clutch inhibitor switch on them.
12-20-06, 03:39 PM
#35
Wankel Me This!!
Thread Starter
i know one of the battery cabels have some white crap on it and it gets hot. how come in my book where you can buy RX7 parts they sell a cluch sensor for 79 to 83
11-03-20, 10:55 AM
#36
Get a good build in the Midwest Banzai racing.
Hi this maybe dumb to ask but I need some help with my motor. Ok my motor does not run still. Me and my dad are thinking of sending it to a shop or to my mazda dealer to see if they will rebuild it in the winter. So here is what I need to ask. Would it be beter to send it to a shop that knows how to rebuild a rotory motor or send it to my mazda dealer ship so they rebuild it? Does any one know how much it will cost? Oh I need to ask another thing. Can someone give me a link on a 12a tubo plz?
Damien
PS: I tryed search did not help.
Damien
PS: I tryed search did not help.
Thread
Thread Starter
Forum
Replies
Last Post