lack of power=cloged cat?
#1
Senior Member
Thread Starter
Join Date: Jul 2006
Location: harrison, ar
Posts: 472
Likes: 0
Received 0 Likes
on
0 Posts
lack of power=cloged cat?
hello, i'm having a lack of power past about 3500 rpm and also a popping noise coming from the carb, i have played with the timing a bit and it seems to have helped a little, because before when i would rev it it would pop a lot more. i have the mixture about right i think. and the 2nd cat will glow red, could this mean its cloged? i have just changed the fuel filter also. i will be getting an rb header soon but i need to be able to drive the rx-7 as my dd because she is my only transportation right now. thanks! 85 gs w/ rb holly 465
#7
Senior Member
Thread Starter
Join Date: Jul 2006
Location: harrison, ar
Posts: 472
Likes: 0
Received 0 Likes
on
0 Posts
ok thanks, also anyone komw what the popping from the carb could be? it still pops under a load. maybe pinging? not really sure what detanation sounds like.
Trending Topics
#10
Senior Member
Thread Starter
Join Date: Jul 2006
Location: harrison, ar
Posts: 472
Likes: 0
Received 0 Likes
on
0 Posts
alright, tommorow i'm going to try to un-bolt the 2nd cat, hopefully the bolts dont snap off, this way i can punch them out and put them back on until i can get an rb system.
#11
Lives on the Forum
The popping and loss of power could be cats, but could also be an ignition issue. A worn cap/rotor or bad plug wires could do this. Inadequate grounding of the engine can also cause issues. Installing a new cap/rotor only takes a few minutes, so unless yours in fairly new, I would suggest trying that before dropping the exhaust system. Good luck.
#12
Senior Member
Thread Starter
Join Date: Jul 2006
Location: harrison, ar
Posts: 472
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Kentetsu
The popping and loss of power could be cats, but could also be an ignition issue. A worn cap/rotor or bad plug wires could do this. Inadequate grounding of the engine can also cause issues. Installing a new cap/rotor only takes a few minutes, so unless yours in fairly new, I would suggest trying that before dropping the exhaust system. Good luck.
#14
Senior Member
Thread Starter
Join Date: Jul 2006
Location: harrison, ar
Posts: 472
Likes: 0
Received 0 Likes
on
0 Posts
ok, so today i got the muffler hooked back up, and i drove her and it was still popping and boging down, now this is the odd part; the timng was just set to factory not long ago, so i thought hmm maybe i'll put it back the way it was when i bought it, and and that was it- now she pulls hard, i dont know why. correct me if im wrong- when set to factory spec the rotor should point to the firewall? so to put it back where it was when i bought it i pulled the dizzy and turned the rotor clockwise; it is now pointing at the clip that holds the dizzy cap on. what do you guys think?
#16
Lives on the Forum
I'm gonna guess that either your front pulley is misaligned, or you lack a true understanding of how to set the timing. But hey, as long as it runs, right?
#17
Senior Member
Thread Starter
Join Date: Jul 2006
Location: harrison, ar
Posts: 472
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Kentetsu
I'm gonna guess that either your front pulley is misaligned, or you lack a true understanding of how to set the timing. But hey, as long as it runs, right?
#18
Lives on the Forum
As long as everything is aligned correctly, and yes the pulley can be put on in four different ways, then the position of the rotor has no part in setting the ignition timing. Clip the lead on the front lower plug wire, and shine the light on the pulley, then rotate the dizzy as needed to align the marks. One thing to note; if your idle speed is over 1000 then remove and plug the vacuum advance lines on the dizzy to ensure that vacuum advance is not influencing your adjustments.
#19
Senior Member
Thread Starter
Join Date: Jul 2006
Location: harrison, ar
Posts: 472
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Kentetsu
As long as everything is aligned correctly, and yes the pulley can be put on in four different ways, then the position of the rotor has no part in setting the ignition timing. Clip the lead on the front lower plug wire, and shine the light on the pulley, then rotate the dizzy as needed to align the marks. One thing to note; if your idle speed is over 1000 then remove and plug the vacuum advance lines on the dizzy to ensure that vacuum advance is not influencing your adjustments.
#24
Lives on the Forum
Well, this thread has suddenly gone to hell in a handbasket...
Yes, your pulley may be off 90 degrees, or 180 even. There is a procedure in the Archives that will walk you through the process of getting everything lined up properly. Not hard to do, just involves looking at the flywheel through the little inspection hatch on the top rear of the motor (by the rat's nest).
Yes, your pulley may be off 90 degrees, or 180 even. There is a procedure in the Archives that will walk you through the process of getting everything lined up properly. Not hard to do, just involves looking at the flywheel through the little inspection hatch on the top rear of the motor (by the rat's nest).