1st Generation Specific (1979-1985) 1979-1985 Discussion including performance modifications and technical support sections

Just sayin Hey, Been gona a couple years...

Thread Tools
 
Search this Thread
 
Old 04-06-07 | 10:56 AM
  #1  
shadowlife25's Avatar
Thread Starter
Cuisinart on Steroids
 
Joined: Aug 2004
Posts: 124
Likes: 0
From: Napa, CA.
Cool Just sayin Hey, Been gona a couple years...

Just wanted to check in and say hi to everyone! I see you're still here Directfreak!
I always loved to watch your dyno vids, and your in car movies

Anyhow, I have sadly sold my Gsl-se. It went to a good home though. I had it pullin 12's too Now it will be babied and go to the track to play regularly.

I now have a Celica GT-4. Great car, but an entirely different beast. I'll always miss my 7. Nothin like showin' up a car that's 20+ years newer on the twisties
Old 04-06-07 | 11:11 AM
  #2  
Jeff20B's Avatar
Lapping = Fapping
iTrader: (13)
 
Joined: Aug 2001
Posts: 15,725
Likes: 83
From: Near Seattle
So get another 1st gen so you can post here again.
Old 04-07-07 | 03:17 PM
  #3  
shadowlife25's Avatar
Thread Starter
Cuisinart on Steroids
 
Joined: Aug 2004
Posts: 124
Likes: 0
From: Napa, CA.
Haha, Jeff! Too long man Great to see ya.
I had actually picked up another SE, but space was an issue so it had to go
I WILL HAVE ANOTHER. Oh yes.... I will.
Old 04-07-07 | 03:17 PM
  #4  
shadowlife25's Avatar
Thread Starter
Cuisinart on Steroids
 
Joined: Aug 2004
Posts: 124
Likes: 0
From: Napa, CA.
DP
Old 04-07-07 | 03:26 PM
  #5  
MaX PoWeR's Avatar
Smoov-e "Dick Like Mine"
iTrader: (2)
 
Joined: Sep 2004
Posts: 542
Likes: 0
From: Nor Cal assassin
shadowlife25 wat were ur mods making the se pullin 12's?
Old 04-07-07 | 08:57 PM
  #6  
GavinJuice's Avatar
Leave A Message

 
Joined: Sep 2003
Posts: 1,454
Likes: 1
From: MN
nothin wrong with a celica
Old 04-08-07 | 06:15 AM
  #7  
shadowlife25's Avatar
Thread Starter
Cuisinart on Steroids
 
Joined: Aug 2004
Posts: 124
Likes: 0
From: Napa, CA.
8lb flywheel
3" exhaust after the header (RB)
Gutted interior paneling and carpet padding
No A/C (entire system removed)
Rats nest = GONE
All electrical wiring in interior and engine bay made over with as short runs as possible
Direct fire ignition, MSD
Balanced all rotors
port job
Balanced e-shaft
pinned
Port matching on intake and exhaust
Stage 3 clutch
Custom Carbon driveshaft
Full RB suspension setup (poly bushings and all)
Tokico Illumina 5 ways
Poly motor mounts
2g turbo tranny
Wilwood rotors (big)
Custom CAI
Custom fuel rail with 880's
Megasquirt EMS
Wet shot of the juice (until I finished my 20B)

All now sold and gone.
It's almost funny: I miss being harassed for driving it :P
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Donald Hampton
2nd Generation Specific (1986-1992)
16
11-23-22 07:38 PM
galvatron10000
Canadian Forum
9
09-08-15 09:50 PM
Steven_McKinley
General Rotary Tech Support
12
09-05-15 11:48 AM
kkev.7788
West RX-7 Forum
0
09-02-15 03:13 AM




All times are GMT -5. The time now is 05:35 PM.