How to use Amsoil Power Foam to clean your carb & engine internals
#1
My FSP Fiesta eats Jettas
Thread Starter
How to use Amsoil Power Foam to clean your carb & engine internals
First, as a carb cleaner I spray a quarter of a can right down the carb while I keep the engine revs up by grabbin' the throttle cable. (I know, the instructions on the can say to use a half a can, but I've found that to be unnecessary.)
The exhaust will smoke like crazy. After about a minute turn off the motor, and while it is still warm spray the carb full of foam and dump it in the intake by opening both sets of butterflies by hand. Turn the motor over by hand to crank the powerfoam into the motor.
Repeat this procedure until you have used about another quarter of a can. Now let the PF work in the motor for anywhere from 30 minutes to several hours. If you've never done it before, leave it in for about an hour or two to be sure that the carbon and gummy deposits get thoroughly softened.
Now is when I usually have a beer and gab with the neighbors, as soon the area will be completely uninhabitable...
Now start the car. It will smoke like crazy and you have to keep it running until the exhaust clears out just enough to take the car out for a drive at highway speeds for at least 30 minutes, although longer is better as you want to make sure that any dislodged carbon gets blown out the exhaust and does not redeposit itself in a worse spot, like an apex seal slot.
(I'm pretty sure that's what happened to me once, but I was able to re-Powerfoam the motor and fix it.)
The end result is a smoother-running motor with better throttle response. I suspect that carbon deposits on the rotors tend to unbalance the motor, but that is just my theory as to why the engines seem to run smoother with noticably less vibration after using the powerfoam treatment.
I have not used Powerfoam to free a carbon-locked motor, but I seem to remember someone on the forum posting that they had successfully used PF to do just that.
Oh, and powerfoam sprays in a stream that then foams up, rather than a spray pattern, so it's easy to get into the spark plug holes and whatnot.
Hope that helps, I have every confidence in Amsoil powerfoam as I've been using the stuff for almost ten years without noting any negative effects other than the one time I mentioned which was my own fault for not driving the hell out of the RX4 after the treatment.
This procedure has been developed by trial and error as well as the time-honored SWAG method
(Scientific wild-*** guessing).
The exhaust will smoke like crazy. After about a minute turn off the motor, and while it is still warm spray the carb full of foam and dump it in the intake by opening both sets of butterflies by hand. Turn the motor over by hand to crank the powerfoam into the motor.
Repeat this procedure until you have used about another quarter of a can. Now let the PF work in the motor for anywhere from 30 minutes to several hours. If you've never done it before, leave it in for about an hour or two to be sure that the carbon and gummy deposits get thoroughly softened.
Now is when I usually have a beer and gab with the neighbors, as soon the area will be completely uninhabitable...
Now start the car. It will smoke like crazy and you have to keep it running until the exhaust clears out just enough to take the car out for a drive at highway speeds for at least 30 minutes, although longer is better as you want to make sure that any dislodged carbon gets blown out the exhaust and does not redeposit itself in a worse spot, like an apex seal slot.
(I'm pretty sure that's what happened to me once, but I was able to re-Powerfoam the motor and fix it.)
The end result is a smoother-running motor with better throttle response. I suspect that carbon deposits on the rotors tend to unbalance the motor, but that is just my theory as to why the engines seem to run smoother with noticably less vibration after using the powerfoam treatment.
I have not used Powerfoam to free a carbon-locked motor, but I seem to remember someone on the forum posting that they had successfully used PF to do just that.
Oh, and powerfoam sprays in a stream that then foams up, rather than a spray pattern, so it's easy to get into the spark plug holes and whatnot.
Hope that helps, I have every confidence in Amsoil powerfoam as I've been using the stuff for almost ten years without noting any negative effects other than the one time I mentioned which was my own fault for not driving the hell out of the RX4 after the treatment.
This procedure has been developed by trial and error as well as the time-honored SWAG method
(Scientific wild-*** guessing).
#5
Rotoholic Moderookie
iTrader: (4)
Hey Guys,
WankelGuy sent this to me to be added to the Article a few weeks back, but with my last few weeks before exams I've been pressed thin for time.
Great info, thanks for sharing it And as promised, when the exams are over in mid-april I'll incorporate this into the article.
I hope my untimelieness didn't frustrate you into posting But again, great info, and the fact that it's from many first-hand experiences of yours makes it even better.
Jon
WankelGuy sent this to me to be added to the Article a few weeks back, but with my last few weeks before exams I've been pressed thin for time.
Great info, thanks for sharing it And as promised, when the exams are over in mid-april I'll incorporate this into the article.
I hope my untimelieness didn't frustrate you into posting But again, great info, and the fact that it's from many first-hand experiences of yours makes it even better.
Jon
#6
This IS a tasty burger!
Join Date: Aug 2003
Location: Nashville, TN
Posts: 403
Likes: 0
Received 0 Likes
on
0 Posts
For an EFI engine.... do I just need to spray it into the spark plug holes for each individual rotor face? Or can I just do one face and then turn over a bunch of times?
#7
Ride 'n Style
Join Date: Dec 2002
Location: Spokane, WA
Posts: 1,929
Likes: 0
Received 0 Likes
on
0 Posts
I spun my engine over with the plugs out to get th foam out... didn't have a large smoke problem when I started it... good info if you've got cats or neighbors that get easily annoyed.
Trending Topics
#8
My FSP Fiesta eats Jettas
Thread Starter
Originally posted by riofrio
For an EFI engine.... do I just need to spray it into the spark plug holes for each individual rotor face? Or can I just do one face and then turn over a bunch of times?
For an EFI engine.... do I just need to spray it into the spark plug holes for each individual rotor face? Or can I just do one face and then turn over a bunch of times?
I'd just spray it down the intake while cranking the motor over after disabling the ignition.
#9
My FSP Fiesta eats Jettas
Thread Starter
I suppose some clarifications are in order at this point.
First, don't be afraid of this procedure, Power Foam will not harm your catalytic converters or exhaust system.
Second, don't waste your time trying to get the stuff out by hand, the most effective cleaning is achieved when the motor is warm and the stuff gets BLOWN out the exhaust. When the motor is running the centrifugal force helps to thoroughly evacuate the apex seal slots, which is important.
Lastly, this is a pretty easy procedure, don't make it more complicated than it really is.
First, don't be afraid of this procedure, Power Foam will not harm your catalytic converters or exhaust system.
Second, don't waste your time trying to get the stuff out by hand, the most effective cleaning is achieved when the motor is warm and the stuff gets BLOWN out the exhaust. When the motor is running the centrifugal force helps to thoroughly evacuate the apex seal slots, which is important.
Lastly, this is a pretty easy procedure, don't make it more complicated than it really is.
#12
This IS a tasty burger!
Join Date: Aug 2003
Location: Nashville, TN
Posts: 403
Likes: 0
Received 0 Likes
on
0 Posts
stupid question... how do I spray the stuff down the intake? i mean, do i need to remove the throttle body to have access to the port or something? I know it's simple, I just haven't messed around in there quite enough yet.
#14
i used seafoam once for a different application, i dont think its the same thing, but it sure as hell smokes like crazy. look for the powerfoam. seafoam doesnt actually foam, if i remember correctly
#15
Former Site Sponsor
Join Date: Feb 2004
Location: Tacoma WA
Posts: 1,052
Likes: 0
Received 0 Likes
on
0 Posts
It's easier to remove the 3 nuts by the throttle body and spray there. Better yet use some 44k in the gas tank with every oil change, it will clean everything from the tank to the engine to prevent the carbon build up. The power foam is great for getting the carbon off the rotors in a not start condition.
We are an amsoil dealer and ship daily.
We are an amsoil dealer and ship daily.
#25
Stu-Tron Get Yo Groove On
iTrader: (4)
Originally Posted by 81WideMariah
soooo...here's a fun thought....what about the guys like me running side-drafts with wrap around intakes??... makes it a little harder to get the foam in there.