Front suspension bits
11-10-01, 02:14 PM
#1
Are you Nucking Futs?
Thread Starter
Join Date: May 2001
Location: Abilene, TEXAS
Posts: 1,235
Likes: 0
Received 0 Likes
on
0 Posts
Front suspension bits
Hello,
I was wondering if anyone out there had replaced their lower control arm or lower ball joints of late?
I do not want to pay the 130 a pop for the LCA’s but it looks like I will.
Also very sloppy steering box. Is my only recourse to buy a $600 Mazda box….any other suggestions.
Thanx.
Scott
I was wondering if anyone out there had replaced their lower control arm or lower ball joints of late?
I do not want to pay the 130 a pop for the LCA’s but it looks like I will.
Also very sloppy steering box. Is my only recourse to buy a $600 Mazda box….any other suggestions.
Thanx.
Scott
11-10-01, 06:37 PM
#2
Senior Member
Join Date: Apr 2001
Location: Arlington, TX, USA
Posts: 561
Likes: 0
Received 0 Likes
on
0 Posts
I replaced my lower ball joints on the drivers side about two years ago, and also replaced all my ruber bushings in the front. It cost me like 600.00 to do it all. I still need a new stearing box though because my front end is more responsive but still has about 1.5 inches of play.
11-10-01, 07:35 PM
#3
Full Member
Join Date: May 2001
Location: San Antonio, Tx
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
Check http://www.mazspeed.com/steeringgear.htm for an excellent description on how to adjust the steering box (three seperate adustments). You probably don't need to replace your box, I thought mine was shot, but it tightened up just fine.
Kerry
Kerry
Last edited by Kerry; 11-10-01 at 07:45 PM.
11-11-01, 11:16 AM
#4
I got a 85, with about 1/2 turn of free play in the steering, I thought since I had the motor out, Id change the steering box too (By the way how in the fek would you replace this thing w/o the motor being out anayways!). I got 3 steering boxes from misc places all over the country and havent found 1 good one yet. 2 Of them had free play the other had poping in it as I turned the sterring wheel. Disasembled the poping one to find a cracked gear on the sector shaft. I know you can get sector shafts new, but as far as the worm and gear nut on the steering rod, I dunno there... But yeah they are expensive as hell!
And for the 85 only a 84 or 85 manual steering will work
so That eliminates a shitload of parts!
On the front ball joints on my 80 i just pressed new ones in, and welded them into place. I knew if I ever had to replace them again, id be screwed but it would get it back on the road for a long long time!
Anyone got a steering box for an 85 that they know works??? Id pay for one, if they knew it worked 100%!
Oh ****, the last one I had was probally ok, dammit! After reading this, I didnt know you could adjust the worm , gear bearings... Dammit....
And for the 85 only a 84 or 85 manual steering will work
so That eliminates a shitload of parts! On the front ball joints on my 80 i just pressed new ones in, and welded them into place. I knew if I ever had to replace them again, id be screwed but it would get it back on the road for a long long time!
Anyone got a steering box for an 85 that they know works??? Id pay for one, if they knew it worked 100%!
Oh ****, the last one I had was probally ok, dammit! After reading this, I didnt know you could adjust the worm , gear bearings...
Dammit....
Last edited by MIKE-P-28; 11-11-01 at 11:44 AM.
11-11-01, 01:10 PM
#5
Banned. I got OWNED!!!
Join Date: Nov 2001
Location: Kingston Ontario
Posts: 414
Likes: 0
Received 0 Likes
on
0 Posts
hey i have a scrap yard here that has 3 first gen rx-7s that i can probibly rip the steering box outa and 3 or 4 secound gens so let me know what u guys need and ill get to work on getting it ( heh its free for me) unless its some huge *** thing so all ill charge is shipping give me a shout on icq or something 52070702
Thread
Thread Starter
Forum
Replies
Last Post
GrossPolluter
Suspension/Wheels/Tires/Brakes
12
08-15-15 10:32 PM