first gen airdams
#1
Full Member
Thread Starter
Join Date: Sep 2005
Location: elyria
Posts: 120
Likes: 0
Received 0 Likes
on
0 Posts
first gen airdams
Does anyone know if an airdam for an 81-85 will fit the 79-80 model? Because I searching for airdams and I seem to prefer the ones that fit that year. Has anyone tried to put one on or know the extent of the modifications to make it fit if they do?
#2
mods,mods,mods
Join Date: Jun 2005
Location: Pennsylvania
Posts: 132
Likes: 0
Received 0 Likes
on
0 Posts
An early 1st gen air dam will not work/fit on your car. I also have a early 1st. gen and
the only one I can find is available through Mazdatrix or Victoria British. I have done
quite a bit of research on this and I dont even think you can modify the later 1st.
gen airdam ti fit.
Pauli
the only one I can find is available through Mazdatrix or Victoria British. I have done
quite a bit of research on this and I dont even think you can modify the later 1st.
gen airdam ti fit.
Pauli
#3
Rotary Enthusiast
Join Date: Jun 2003
Location: Calgary; AB
Posts: 1,288
Likes: 0
Received 0 Likes
on
0 Posts
anything will fit it all depends on how bad you want to put it on your car, the amount of patience you have getting it too fit and of course a money factor...
#4
it will fit !!!! not to much work to do also. !!!!! not difficult either. !!!! just cut the air dam around the bumper end caps and install. not hard, will work, may be will look good If you fit it good anuff. easier way remove early bumper repalce with late bumper install airdam no cutting assured it will look right.
some people are just going to jump out and tell you anything will not fit/work good luck
some people are just going to jump out and tell you anything will not fit/work good luck
#5
Junior Member
Join Date: Oct 2005
Location: Australia
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
i didnt hav any trouble fitting this bumper on my 80 model....its also for s2 & s3.
Also if you visit mariahmotorsports.com all their kits are made to fit all 1st gens not just s2 & s3.
Also if you visit mariahmotorsports.com all their kits are made to fit all 1st gens not just s2 & s3.
#6
Full Member
Thread Starter
Join Date: Sep 2005
Location: elyria
Posts: 120
Likes: 0
Received 0 Likes
on
0 Posts
ok
well i am doing away with the front bumper and going to use the airdam, which i know leaves a gap where it is supposed to mount to the bumper. so i waiting to do the fab till i find out what i can use for an airdam so i can make it all flush.
#7
Savanna Rx-7
Originally Posted by JAGuiD
i didnt hav any trouble fitting this bumper on my 80 model....its also for s2 & s3.
Also if you visit mariahmotorsports.com all their kits are made to fit all 1st gens not just s2 & s3.
Also if you visit mariahmotorsports.com all their kits are made to fit all 1st gens not just s2 & s3.
JAGuiD,
they are talking about lip/chin spoilers, not full bumper replacement types.
kenn
Trending Topics
#9
Full Member
Thread Starter
Join Date: Sep 2005
Location: elyria
Posts: 120
Likes: 0
Received 0 Likes
on
0 Posts
I know what they are talking about. I just wanted to know if i could use the airdam for an 81-85, if so, I will put it on and fab it so it is flush. I was just wondering because the fenders/bumper are different on the later first gens.
Thread
Thread Starter
Forum
Replies
Last Post
demetlaw
3rd Generation Specific (1993-2002)
6
10-02-15 06:22 PM