Exhaust Video / Sound Clips - Post em here
Thread Starter
Senior Member
Joined: Sep 2001
Posts: 373
Likes: 1
From: California
Exhaust Video / Sound Clips - Post em here
Since deciding on what exhaust to get largely depends on the sound, a few members and I thought it would be a good idea to get a thread going and make it a sticky. So please post your video clips that have sound (or just the sound clips). Make sure to describe your setup, including all the exhaust components, single or TT, and type of port.
Thanks everyone,
Tom
Thanks everyone,
Tom
Thread Starter
Senior Member
Joined: Sep 2001
Posts: 373
Likes: 1
From: California
Originally posted by SilverOckt and hosted by GotBoostd7
midpipe, Greddy Power Extreme
midpipe, RB dual tip
Borla XR-1, RB dual tip #1
Borla XR-1, RB dual tip #2
Borla XR-1, RB dual tip, rev to 4500 rpms
Oh, btw...I am SOOOOOO glad you did this!! I was thinking about changing to RB dual tip with a Borla XR1!! You just sold me on it!! Sounds EXCELLENT!
Here's my annoying *** setup...ATR catback with dp/mp. Tone is actually okay above 4000 rpm, sounds like a rocket ship taking off. But it is just toooo damn loud!
ATR catback, ATR midpipe [/B]
midpipe, Greddy Power Extreme
midpipe, RB dual tip
Borla XR-1, RB dual tip #1
Borla XR-1, RB dual tip #2
Borla XR-1, RB dual tip, rev to 4500 rpms
Oh, btw...I am SOOOOOO glad you did this!! I was thinking about changing to RB dual tip with a Borla XR1!! You just sold me on it!! Sounds EXCELLENT!
Here's my annoying *** setup...ATR catback with dp/mp. Tone is actually okay above 4000 rpm, sounds like a rocket ship taking off. But it is just toooo damn loud!
ATR catback, ATR midpipe [/B]
Originally posted by nocab72
My current setup: GT35/40 w/wastegate dumped back to DP, RX7store midpipe & JIC Bullet Titanium Exhaust.
WOT @ the track, don't laugh at my ET, bow to the MPH...
http://flathat.woodstream.net/Columb...g/12.1@123.WMV (1.7Mb)
Idling just after new pineapple large street ported motor installation (smoke & crap is from new motor, lol)
http://flathat.woodstream.net/Columb...et_Port_IV.WMV (9.5Mb)
My current setup: GT35/40 w/wastegate dumped back to DP, RX7store midpipe & JIC Bullet Titanium Exhaust.
WOT @ the track, don't laugh at my ET, bow to the MPH...
http://flathat.woodstream.net/Columb...g/12.1@123.WMV (1.7Mb)
Idling just after new pineapple large street ported motor installation (smoke & crap is from new motor, lol)
http://flathat.woodstream.net/Columb...et_Port_IV.WMV (9.5Mb)
Full Member
Joined: Sep 2001
Posts: 132
Likes: 0
From: Isla Vista (Santa Barbara), CA
Idling just after new pineapple large street ported motor installation (smoke & crap is from new motor, lol)
Full Member
Joined: Sep 2001
Posts: 132
Likes: 0
From: Isla Vista (Santa Barbara), CA
GT-spec anyone?
Does anybody have and sound clips or vids of an FD w/ the A'pex GT-spec catback? I know this is pretty much the highest flowing catback for the FD, and I like its looks even if its a bit ricey. Anyone?????
Trending Topics
03 Cobra Killer
Joined: Jan 2002
Posts: 1,423
Likes: 0
From: All Over
Originally posted by Droops83
Damn Nocab, sounds crazy . . . does the car always idle that lumpy or is that just cuz the motor had just been installed before that vid? Nice car man.
Damn Nocab, sounds crazy . . . does the car always idle that lumpy or is that just cuz the motor had just been installed before that vid? Nice car man.
K
Weird Cat Man
Joined: Aug 2001
Posts: 2,868
Likes: 3
From: A pale blue dot
What is really needed is a standardized clip... Many video camera mics vary in their ability to record certain ranges...
Maybe the next RX-7 meet I go to where there will be a lot of cars I'll take my camera and get a clip of every car and make it all one movie so that the exhausts can be accurately compared.
Brian
Maybe the next RX-7 meet I go to where there will be a lot of cars I'll take my camera and get a clip of every car and make it all one movie so that the exhausts can be accurately compared.
Brian
Thread Starter
Senior Member
Joined: Sep 2001
Posts: 373
Likes: 1
From: California
Originally posted by Wargasm
What is really needed is a standardized clip... Many video camera mics vary in their ability to record certain ranges...
Maybe the next RX-7 meet I go to where there will be a lot of cars I'll take my camera and get a clip of every car and make it all one movie so that the exhausts can be accurately compared.
Brian
What is really needed is a standardized clip... Many video camera mics vary in their ability to record certain ranges...
Maybe the next RX-7 meet I go to where there will be a lot of cars I'll take my camera and get a clip of every car and make it all one movie so that the exhausts can be accurately compared.
Brian
Make sure you take a notepad and pen with you and have each car owner right down his mods/pieces/engine port.-Tom
Full Member
Joined: Jun 2002
Posts: 247
Likes: 0
From: Del Rio TX
Re: GT-spec anyone?
Originally posted by Droops83
Does anybody have and sound clips or vids of an FD w/ the A'pex GT-spec catback? I know this is pretty much the highest flowing catback for the FD, and I like its looks even if its a bit ricey. Anyone?????
Does anybody have and sound clips or vids of an FD w/ the A'pex GT-spec catback? I know this is pretty much the highest flowing catback for the FD, and I like its looks even if its a bit ricey. Anyone?????
does anyone have those nocab videos in mpeg format? i use linux so i cant really use windows media player...
any format besides WMV would be great if anyone could convert them or something.
any format besides WMV would be great if anyone could convert them or something.
Last edited by jacobcartmill; Jan 8, 2003 at 01:32 AM.
Originally posted by forcefed1
great thread! im going to add a borla to my midpipe this weekend. ill record the before and after too. except I donna what exhaust I have on there
great thread! im going to add a borla to my midpipe this weekend. ill record the before and after too. except I donna what exhaust I have on there
Thats great Forcefed.....keep em comming.
The more there is the better it helps peeps out!
For your old exhaust , take a look underneath when you put the Borla on, and see what it is(obviously HAHA).
If you dont see any writing to tell you what it is, just let us know your set up......DP, MP, diameter etc, and we will go by that.
Now if we can just make this a"sticky" like we been asking!! You can see people are interested.
cheers
Shawn
Originally posted by Mazdabation
Dont want to lose this.................bump
Dont want to lose this.................bump
I know this is the 3rd gen forum but, could someone get the 20b guys to contribute to this as well. Those sound so f*cking tight.
Rotary Enthusiast
Joined: May 2002
Posts: 1,205
Likes: 0
From: Tallahassee, FL
Originally posted by Wargasm
What is really needed is a standardized clip... Many video camera mics vary in their ability to record certain ranges...
Maybe the next RX-7 meet I go to where there will be a lot of cars I'll take my camera and get a clip of every car and make it all one movie so that the exhausts can be accurately compared.
Brian
What is really needed is a standardized clip... Many video camera mics vary in their ability to record certain ranges...
Maybe the next RX-7 meet I go to where there will be a lot of cars I'll take my camera and get a clip of every car and make it all one movie so that the exhausts can be accurately compared.
Brian
Senior Member
Joined: Feb 2001
Posts: 723
Likes: 0
From: Bellingham, WA
HKS Super Dragger w/ 2.75" ID Midpipe
http://www.fatboyraceworks.com/~ndah...s/DSCF0243.AVI
http://www.fatboyraceworks.com/~ndah...s/DSCF0243.AVI
